I ran into a very frustrating problem yesterday, hopefully someone in
wlug knows the answer..
Verne has 4 sound devices; onboard sound, two PCI cards, and a USB
transmitter. When I first set up breezy I had them loading as
/dev/dsp onboard
/dev/dsp1 first PCI
/dev/dsp2 second PCI
When he first got the USB transmitter it kept coming up as /dev/dsp1 and
I managed to fix that by listing snd-intel8x0 and snd-ens1371 in
/etc/modules, forcing the module for the onboard sound and two PCI cards
to load earlier.
Yesterday I upgraded to dapper and now all the sound devices come up in
completely unpredictable order, not even the same on two consecutive
boots. Even though the correct modules are still listed in /etc/modules.
Is there a proper way to force devices to get detected in the order I want?
(brought back onlist)
> Another example, USB again...
> From http://www.linuxjournal.com/article/7316
>
>> A lot of devices are very difficult to distinguish from another, e.g.
>> EPSON has the same USB ID's for a lot of printer models and you need to
>> query the printer information with a vendor specific protocol
>>
>
> Has the situation changed? Isnt the 'serial no.' you mention the same as the
> USB ID discussed above?
>
Ok, so it doesn't work for all USB devices. Mice are probably the same.
Anything with a filesystem or a unique serial, or MAC address, etc,
however is fine. So, ok, multiple identical printers are probably a
problem. At this point you might have to resort to "get different
printers", or "leave them plugged into the same USB port, perhaps on an
external HUB", or "buy an external print server that does ethernet -> USB.
In terms of sound cards[1], you could use the PCI ID to define the order
in which sound cards are brought up. This doesn't change - or it
shouldn't change, unless you have faulty/crazy hardware - unless you
shift the physical slot the device is plugged into.
[1] or anything, even including USB devices as long as you are prepared
to put them on the same port every time. Use the USB *bus* ID in that
case, not the PCI ID, obviously :)
The WLUG Mailing List is the discussion-list extension of the Waikato
Linux Users Group (Incorporated).
As such, we expect members of this list to adhere to the principles
espoused in the official WLUG Charter[1], in particular, Rule 6, which
covers the activities on this mailing list.
While this is an Acceptable Use Policy, the WLUG Committee do recognise the
need for informal discussion among list members, and draconian administration
is not the goal here. Please keep in mind, however, that your comments to
this list do represent the WLUG, and while it is good to be seen as an
organisation with a sense of humour, some comments may do major harm to our
credibility as a serious advocate of GNU/Linux and all things Free Software/
Open Source related.
List discussion should
* be honest
* accentuate the positive, without hyperbole or blatant
misrepresentation
* maintain a reasonable level of spelling and grammar
* not indulge in ad hominem attacks
* not continue inflammatory or abusive threads
* not be unprofessional or petty, especially with respect to the
names of other software companies
* not promote or denigrate political, cultural, or religious views
* not indulge in marketing or advertising, other than on a private
sale basis, or advertising of jobs - which may be announced
once only
* not reproduce copyrighted material without permission from the
copyright holder
* not defame any person or organisation
Posters who consistently violate these guidelines will be dealt with at
the discretion of the List Maintainer.
If you feel you have been unfairly dealt with, you have recourse to any
member of the WLUG Committee[2].
Certain mailing list etiquette should also be maintained:
* please use only plain text (not HTML)
* reply inline or below when quoting, rather than on top
* trim quotes (don't reply quoting a 10 page message with
a single line of reply)
If you have any questions, start reading at
http://www.gweep.ca/~edmonds/usenet/ml-etiquette.html.
These points have been established over a long time on this list. If you
want to question them, please do it off list. As list users, use your
discretion when pulling people up over etiquette - please reply off
list, and if there is a serious breach, the list administrator will probably
have dealt with it off-list already.
[1] http://www.wlug.org.nz/WlugCharter
[2] http://www.wlug.org.nz/WlugCommittee
Thank everyone
Success! I started at the command line with
the ip address but then I needed the subnet mask and the
gateway so I took Ian's advise and used the gui. The plus is
that I can switch back to DCHP really easily.
Regards John
> There are simpler ways to do this on Ubuntu. I can't
> remember the exact menu location but on my Debian (which
> is similar) it is Places, Administration, Networking and
> you can do it all using the GUI with a minimum of fuss.
>
> --
> Ian McDonald
> Web: http://wand.net.nz/~iam4
> Blog: http://imcdnzl.blogspot.com
> WAND Network Research Group
> Department of Computer Science
> University of Waikato
> New Zealand
I just googled and found:
ifconfig eth0 <number provided>
Is it as simple as just doing this??
If yes! do I need to undo this when I am finished??
John.
> Hello all,
> I am trying to update my system and went to an
> internet cafe to use their network. However, they told me
> I need to add their ip address (Which they gave to me on a
> written note) I have never had to do this before and have
> no idea how to do it in Ubuntu.
> Will some one please help with this?
> Regards John
>
> _______________________________________________
> wlug mailing list | wlug(a)list.waikato.ac.nz
> Unsubscribe:
> http://list.waikato.ac.nz/mailman/listinfo/wlug
I forgot to hit the reply all button.. Sorry:(
----- Original Message Follows -----
> Sorry, missed that bit...
>
I reread everything and I came to the conclusion that I need
to:
sudo ethconfig eth0 <number>
Then when I am finished I may have to check to see if I need
to reset my loopback number: 127.0.0.1
Does this seem right to you??
John
Thank you I will try again tommorrow afternoon :)
Regards John
----- Original Message Follows -----
> No. Leave the loopback interface alone.
>
> jaytee(a)clear.net.nz wrote:
> > ----- Original Message Follows -----
> >> Sorry, missed that bit...>
> >
> > I reread everything and I came to the conclusion that I
> > need to:
> > sudo ethconfig eth0 <number>
> sudo ifconfig eth0 ...
>
> not ethconfig
>
>
> > Then when I am finished I may have to check to see if I
> > need to reset my loopback number: 127.0.0.1
> > Does this seem right to you??
> > John
>
> --
> Don Gould
> www.thinkdesignprint.co.nz - www.tcn.bowenvale.co.nz -
> www.bowenvale.co.nz - www.hearingbooks.co.nz - SkypeMe:
> ThinkDesignPrint
>
>
> _______________________________________________
> wlug mailing list | wlug(a)list.waikato.ac.nz
> Unsubscribe:
> http://list.waikato.ac.nz/mailman/listinfo/wlug
No. Leave the loopback interface alone.
jaytee(a)clear.net.nz wrote:
> ----- Original Message Follows -----
>> Sorry, missed that bit...>
>
> I reread everything and I came to the conclusion that I need
> to:
> sudo ethconfig eth0 <number>
sudo ifconfig eth0 ...
not ethconfig
> Then when I am finished I may have to check to see if I need
> to reset my loopback number: 127.0.0.1
> Does this seem right to you??
> John
--
Don Gould
www.thinkdesignprint.co.nz - www.tcn.bowenvale.co.nz -
www.bowenvale.co.nz - www.hearingbooks.co.nz - SkypeMe: ThinkDesignPrint
Hello all,
I am trying to update my system and went to an
internet cafe to use their network. However, they told me I
need to add their ip address (Which they gave to me on a
written note) I have never had to do this before and have no
idea how to do it in Ubuntu.
Will some one please help with this?
Regards John